Replace T8 Fluorescent Lamps with T8 Led Tubes

For decades now, the T8 fluorescent has dominated our homes and our workplaces as the preferred form of lighting. Its dominance is due to the fact it produces quality light and it is very efficient. They also last for longer than its immediate alternatives. Its dominance is about to lessen though. T8 LED tube is the new player in the lighting arena and it bears a lot of promises. Besides being more efficient than the T8 fluorescent, it is mercury free, easier to control and is dimmable.

Installation guide for T8 LED tubes

  • Safety first

Switch off the electricity. Put “lockout” tag to ensure to ensure no one turns it back up. Put a note close to the circuit breaker explaining that you are working on a fixture within the building and so the breaker should be kept off until you complete the task. Also, wear eye protection to guard your eyes against harm should an old fluorescent tube break while you are removing it. It is also important that you confirm your source supplies between 120V and 240V.

  • Remove the bulbs and the ballast

Some fluorescent lamps are covered using plastic or glass fixtures. Remove the fixture to access and remove the bulb. Take care not to damage it as it is very fragile. Remove the cover of the housing (tombstones) to reach the ballast. Undo any wires leading into and out of the ballast and unscrew it from the housing assembly. Ensure to leave enough of the neutral and live wires for later rewiring. Dispose of the bulb and the ballast responsibly.

  • Rewire the unit

Connect the wires correctly. To achieve this, it’s advisable that you follow the instructions on the box. You can either use connectors or just twist the wires together. In many installations, the wires usually consist of two yellow on the left, two red and two blue on the right. Put together all the wires from one side with one lead from the incoming circuit wires and those from the other side with the other lead. However, it is important to note that some LED has both the hot and the neutral on one end of the connection. Therefore, you need to refer to the manufacturer’s instruction if you are not sure of the configuration.






Location: England, UK

Comments

  1. Be Happy17 July 2020 at 23:11

    Allegations of sexual harassment, musician Meesha Shafi has filed a Rs 2 billion lawsuit against actor-singer Ali Zafar.  Find Meesha Shafi's latest News.

    ReplyDelete

Post a Comment

Popular posts from this blog

Mid-Power LEDs: Less Expensive for LED Lights

Image
  Mid-power LEDs Do you see that sleek, ultra-thin HD TV set in front of you? Well, its existence has been made possible by mid-power LEDs. Which can be  powered the shift from old cold CRT backlight TV. These are tiny LEDs measuring a few millimeters square. Courtesy of their size and weight, hundreds of them can be fitted unto a single light source but still weigh less than 250 grams. They can be pa packaged densely compared to high-power white LEDs. They offer relatively high-power white LEDs and a more uniform appearance. They also consume less power. Mid-power is for many reasons touted as the best alternative for LED lighting. High-power, mid-power, and low power LEDs To get a better grasp on mid-power LEDs is important to understand the three classifications of LEDs Low power They were the earliest LEDs in the market and were mostly used for indicator lights and identifying the status of machine condition. High power They are costly thus were initially used for research. Comme
Read more

An Introduction to Brushless Direct Current (BLDC) Motors

Image
The growing popularity Has your phone vibrated today? Well then, you just experienced a  brushless DC (BLDC) motor  in action.  BLDC motors  are synchronous motors that are powered by direct current through a drive module or controller. BLDC motors have witnessed rapid growth in popularity owing to their construction that makes them superior to the brushed counterparts. BLDC motor construction Rotor The rotor is made up of permanent magnets and its number of poles (North and South poles) varies from two to eight pairs. The permanent magnets are made from ferrite magnets. However, permanent magnets made from rare earth alloys are increasingly becoming popular owing to the advancement in technology. Rare earth alloys offer more magnetic density per volume while enabling the rotor to compress further for the same amount of torque. Such alloys also improve the size to weight ratio. There are two rotor designs for BLDC motors; the inner rotor and the outer rotor design. I
Read more

Little Know more about Brush-less Motors

Image
Brushless motors Brushless differs from conventional dc motors in the sense that it does not have brushes. Commutation is done using electronic drives to feed power to the stator windings. They consist of a rotor which is in the form of a permanent magnet and a stator that is in the form of polyphase armature windings. A  brushless DC motor  can be constructed in two ways; one is by placing the rotor outside the core and the other is by placing the rotor inside the core. How a brushless motor works Brushless motors are driven by electronic drives that  switch  the supply voltage between the stator windings while the rotor turns. There is a transducer that monitors the position of the rotor as it turns and conveys the information to an electronic controller. The controller then decides which stator winding to be energized based on the position of the rotor. Electronic drives are made up of two transistors each phase which is run by a microprocessor. The magnetic field i
Read more